描述
Pleated Polypropylene Filter Cartridges
- Melt blown polypropylene filter medium provides efficient particle removal, high contaminant-holding capacity and wide chemical compatibility
- Available in retention ratings of 0.25 to 30 micron (μm)
- Protective netting is color coded for easy identification
- Small diameter fibers provide high flow rates at low pressure drops
- Manufactured under an ISO 9001 quality system
规格
Performance Specifications
Filter grades
- 0.25, 0.5, 1, 2, 3, 5, 10, 30 μm
Maximum forward differential pressure
- 4.8 bard (70 psid) @ 20 °C (68 °F)
- 2.8 bard (40 psid) @ 65 °C (150 °F)
Recommended change-out differential pressure1
- 2.4 bard (35 psid)
Food and water contact use
- Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.
Rinse-up
- Rinse-up to 18 Megohm-cm with a minimum of throughput.
Product Specifications
Materials of construction
| Filter media: | Melt blown polypropylene |
| Support material: | Polypropylene |
| Hardware: | Polypropylene |
| Sealing: | Thermal bond |
| Gaskets/O-rings: | Silicone elastomer (standard), nitrile, hydrocarbon rubber, white silicone, fluorocarbon elastomer, expanded PTFE, FEP encapsulated silicone |
Dimensions (nominal)
| Outside diameter: | 6.4 cm (2.5 in.) |
| Lengths: | 24.8 cm (9.75 in.), 25.4 cm (10 in.), 49.5 cm (19.5 in.), 50.8 cm (20 in.), 68.6 cm (27 in.), 74.3 cm (29.25 in.), 76.2 cm (30 in.), 100.3 cm (39.5 in.), 102 cm (40 in.) |
Color Code Chart For Quantum P Series Filters
| Cartridge Designation | Filter Grade | Netting Color |
| 002 | 0.25 | Yellow |
| 005 | 0.5 | White |
| 010 | 1 | Green |
| 020 | 2 | White with orange swatch |
| 030 | 3 | Orange |
| 050 | 5 | Blue |
| 100 | 10 | Red |
| 300 | 30 | Purple |
1 Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
性能
Liquid Retention Ratings (μm) (by ASTM F-795 Test)
| Cartridge Designation | 90% Efficiency | >99.9% Efficiency |
| QMPT 002 | 0.25 | 1 |
| QMPT 005 | 0.5 | 1.2 |
| QMPT 010 | 1 | 2.5 |
| QMPT 020 | 2 | 5 |
| QMPT 030 | 3 | 7 |
| QMPT 050 | 5 | 12 |
| QMPT 100 | 10 | 15 |
| QMPT 300 | 30 | 40 |
The particle removal data given below was obtained from laboratory tests using dilute aqueous suspensions of AC Fine Test Dust at a flow of 9.5 lpm/25.4 cm (2.5 gpm/10 in) element at a temperature of 20°C (68°F). The removal efficiencies were determined with an electronic particle counter, and the values given represent the minimum efficiencies obtained. The removal rating of any filtration device will be influenced by the nature of the fluid, its viscosity, flow rate, type of contaminant, and temperature. Consult your local representative for more information regarding Pall's test procedures.
Typical Flow vs. Differential Pressure for Application Sizing
Unit conversion: 1 bar = 100 kPa
Flow rate is for a 25.4 cm (10 in) cartridge. For liquids other than water, multiply differential pressure by fluid viscosity (cP).
类型
Filter Cartridges
应用
Auto LOH for Stamping, Heavy Lubrication, Material Handling, Auto Painting/Coating Zinc Phosphate Bath, Midstream Process Water, Midstream Process Water, Midstream Process Water, Midstream Process Water
订购信息
Pall Part Number = QMPT [1] – [2] U [3] – [4] – [5]
Table 1
| Code | Filter grades (μm) |
| 002 | 0.25 |
| 005 | 0.5 |
| 010 | 1 |
| 020 | 2 |
| 030 | 3 |
| 050 | 5 |
| 100 | 10 |
| 300 | 30 |
Table 2
| Code | Cartridge lengths (cm / in.) nominal |
| 975 | 24.8/9.75 |
| 100 | 25.4/10 |
| 195 | 49.5/19.5 |
| 200 | 50.8/20 |
| 270 | 68.6/27 |
| 292 | 74.3/29.25 |
| 300 | 76.2/30 |
| 395 | 100.3/39.5 |
| 400 | 102/40 |
Table 3
| Code | Gasket/O-ring materials |
| S | Silicone (standard O-rings) |
| N | Nitrile (standard gaskets) |
| V | Fluorocarbon elastomer |
| E | Hydrocarbon rubber |
| M | White silicone (222 O-rings) |
| T | FEP encapsulated silicone (O-rings) |
| T | Expanded PTFE (gaskets) |
Table 4
| Code | End configurations |
| Blank | DOE with elastomer gasket seals and end caps |
| 1X | DOE, 2.54 cm (1in) extended core |
| M2 | SOE flat closed end, fits housings with 020 O-ring post |
| M3 | SOE flat closed end, external 222 O-rings (retrofits other manufacturers’ Code 0)2 |
| M3H | SOE large diameter closed end, external 222 O-rings |
| M4 | SOE fin end, external 222 O-rings with locking tabs |
| M5 | DOE, internal 120 O-rings (retrofits 213 O-ring style)2 |
| M6 | SOE flat closed end, external 226 O-rings (retrofits other manufacturers’ Code 6)2 |
| M7 | SOE fin end, external 226 O-rings (retrofits other manufacturers’ Code 7)2 |
| M8 | SOE fin end, external 222 O-rings (retrofits other manufacturers’ Code 5)2 |
| M10 | DOE, internal O-rings (fits other manufacturers’ housings)2 |
| M20 | SOE, internal O-ring (same as M10), closed end with deep recess |
2 For details, contact Pall Corporation.
Table 5
| Code | Bubble test option |
| Blank | No bubble test |
| B | 100% bubble test |
分类信息
Automotive, Mobile OEM, Primary Metals, General Industrial, General Industrial, General Industrial, General Industrial, General Industrial
检查
Earn 10% off* your next order online by leaving a review of this product. Please login to your account to leave a review. We appreciate and value your feedback.
*Subject to Terms and Conditions.
