1. 首页/
  2. Food & Beverage/
  3. 啤酒-精酿啤酒/
  4. 进水/
  5. LMO Non-Metallic Series Filter Housings
LMO Non-Metallic Series Filter Housings product photo Primary L

LMO Non-Metallic Series Filter Housings

Durable, Corrosion Resistant
Design for Liquid Applications

The Pall range of non-metallic single cartridge housings offers an economical answer to low flow requirements. Non-metallic housings are available with polypropylene heads and a choice of polypropylene or SAN bowls to suit a range of chemical applications. Filter assemblies should not be used with fluids incompatible with the materials of construction. These industrial designed housings are ideally suited for use with low flows where a metallic housing is not required.

  • Cost effective alternative to stainless steel in corrosive fluid applications
  • Accepts 20 in. (50.8 cm) DOE or Pall M5 (Code 5) style cartridge
  • Fixed guides in head and shell ensure proper alignment and seating of cartridges
  • Manufactured from materials which are listed for Food Contact Applications in Title 21 of the U.S. Code of Federal Regulations
了解更多


Contact Us
* 必填项

Durable, Corrosion Resistant
Design for Liquid Applications

The Pall range of non-metallic single cartridge housings offers an economical answer to low flow requirements. Non-metallic housings are available with polypropylene heads and a choice of polypropylene or SAN bowls to suit a range of chemical applications. Filter assemblies should not be used with fluids incompatible with the materials of construction. These industrial designed housings are ideally suited for use with low flows where a metallic housing is not required.

  • Cost effective alternative to stainless steel in corrosive fluid applications
  • Accepts 20 in. (50.8 cm) DOE or Pall M5 (Code 5) style cartridge
  • Fixed guides in head and shell ensure proper alignment and seating of cartridges
  • Manufactured from materials which are listed for Food Contact Applications in Title 21 of the U.S. Code of Federal Regulations

4.1 (9)Materials of Construction

  • Head1
       LMO-U: Polypropylene
       LMO-UP: Polypropylene
  • Shell
       LMO-U: Polypropylene
       LMO-UP: SAN (Styrene Acrylonitrile)

Maximum Operating Pressure

  • LMO-U: 8.6 bar (125 psig) @ 52 °C (125 °F)
  • LMO-UP: 6.9 bar (100 psig) @ 66 °C (150 °F)

Connections

  • Inlet/outlet: 3/4" NPT

Shell O-rings

  • Ethylene propylene (standard), Nitrile, neoprene, fluorocarbon elastomer

Standard Colors

  • LMO-U: Opaque with blue head and shell
  • LMO-UP: Blue head and clear shell

Food and Water Contact Use

Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.

Selection Criteria

LMO-U LMO-UP
Ultra Violet Light Recommended Fair
Strong Acid Recommended Fair
Weak Acid (<20%) Recommended Recommended
Organic Solvent Recommended Not Recommended
Strong Oxidizing Agent Recommended Not Tested
Weak Base (<20%) Recommended Recommended
Strong Base Recommended Fair
This housing is not recommended for compressed air or gas service. It is suitable for use with fully compatible (which do not soften, swell or adversely effect the product or its materials of construction) liquids only. This housing is not recommended for acid service at the pressure shown. Please contact Pall for detailed compatibility information.

NOTE: Use of this product in a manner other than in accordance with Pall’s current recommendations may lead to injury or loss. Pall cannot accept liability for such injury or loss.

Dimensional Date (Nominal)

Dimensions cm (in.)
Model Liquid Flow Rate2 lpm (gpm A B Weight kg (lb)
LMO20U-3/4 to 75.7 (20) 57.2 (22.5) 13.7 (5.38) 4.1 (9)
LMO20UP-3/4 to 75.7 (20) 57.2 (22.5) 13.7 (5.38)

Housing Differential Pressure vs. Liquid Flow Rate

Housing Differential Pressure vs. Liquid Flow Rate
Unit conversion: 1 bar = 100 kpa

For liquids other than water, multiply differential pressure by the specific gravity of the fluid.

LMO Non-Metallic Housing Side View

LMO Non-Metallic Housing Top View

1Housing head has mounting bosses, which accept self-tapping screws for attaching a bracket to the housing.
2Dependent upon cartridge selection, fluid viscosity and allowable pressure drop.
Housings, Vessels, or Assemblies
General F&B, Incoming Water, Incoming Water, General F&B
This information is a guide to the part number structure and possible options. For availability of specific options and housing details, please contact Pall.

Example Part Number: LMO 20 U -3/4 (See bold references in table below)

Part Number: LMO 20  < Code from Table 1 > -3/4

Table 1 - Material of Construction

Code Materials of Construction
U Polypropylene
UP SAN
Housings, Beer (Craft/Micro Breweries), Beer (Corporate), Housings

Earn 10% off* your next order online by leaving a review of this product. Please login to your account to leave a review. We appreciate and value your feedback.

*Subject to Terms and Conditions.